FNX940 v1.0
Download Torrent
Opens in your torrent client (e.g. qBittorrent)
Health
Dead0/0
Info Hash7EE6B2766FE9FADD750F56E906ABAB824DCA4926
Peers Updated16 hours ago (2026-03-30 05:22:53)
Description
# FNX940
A frame for FNX-9 and FNX-40 part kits
by nguyenkvvn
minor geometry referenced from the FNS940 model by TMS
## Description
The FNX is a polymer hammer-fired pistol availible in 9mm and .40 S&W. It is a precursor to the FNS series of pistols. It uses plates for rails, rather than a monolithic locking block or integrated into the fire-control housings. It is only availible commercially in full-size configuration.
Geometry that was referenced from the FNS940 model by TMS includes but is not limited to: magazine button cut-out, magazine button spring relief, trigger pin location.
## Materials Required
You will need a set of each below for each FNX-9/40 you make.
This model is compatible with any FNX-9 or FNX-40 parts kit. It is *not* compatible with the FNX-45 or FNX-45 Tactical.
- x1 **Parts Kit** - Procure a parts kit of your preferred caliber.
- x1 **Magazine** - Procure a magazine of your preferred caliber
## Instructions
* Print with PLA+, or Tough PLA.
* Tree supports are recommended
* Print *rails down* on the bed
* It is imperative your printer has no elephant footing- otherwise the rail plates may not seat properly!
_Assembly instructions can be found in the rich-text PDF included._
## Change Log
- v1.0: Release
* Promotion to release
- v0.4: Private Beta Candiate 4
* Revised front takedown lever clearances
* Omitted horseshoe geometry
* Refined front rail fitment geometry
- v0.3: Private Beta Candiate 3
* Loosened tolerances for rear rail plates
* Loosened tolerances for front rail / locking block places
- v0.2: Private Beta Candiate 2
* Added right-hand safety selector cutout
* Re-introduced some takedown-lever geometry
* Tightened tolerances for the front locking block plates
- v0.1: Private Beta Candidate 1
* Initial commit
## License
No license selected
A frame for FNX-9 and FNX-40 part kits
by nguyenkvvn
minor geometry referenced from the FNS940 model by TMS
## Description
The FNX is a polymer hammer-fired pistol availible in 9mm and .40 S&W. It is a precursor to the FNS series of pistols. It uses plates for rails, rather than a monolithic locking block or integrated into the fire-control housings. It is only availible commercially in full-size configuration.
Geometry that was referenced from the FNS940 model by TMS includes but is not limited to: magazine button cut-out, magazine button spring relief, trigger pin location.
## Materials Required
You will need a set of each below for each FNX-9/40 you make.
This model is compatible with any FNX-9 or FNX-40 parts kit. It is *not* compatible with the FNX-45 or FNX-45 Tactical.
- x1 **Parts Kit** - Procure a parts kit of your preferred caliber.
- x1 **Magazine** - Procure a magazine of your preferred caliber
## Instructions
* Print with PLA+, or Tough PLA.
* Tree supports are recommended
* Print *rails down* on the bed
* It is imperative your printer has no elephant footing- otherwise the rail plates may not seat properly!
_Assembly instructions can be found in the rich-text PDF included._
## Change Log
- v1.0: Release
* Promotion to release
- v0.4: Private Beta Candiate 4
* Revised front takedown lever clearances
* Omitted horseshoe geometry
* Refined front rail fitment geometry
- v0.3: Private Beta Candiate 3
* Loosened tolerances for rear rail plates
* Loosened tolerances for front rail / locking block places
- v0.2: Private Beta Candiate 2
* Added right-hand safety selector cutout
* Re-introduced some takedown-lever geometry
* Tightened tolerances for the front locking block plates
- v0.1: Private Beta Candidate 1
* Initial commit
## License
No license selected